Nissan Rogue Service Manual: P0461 fuel level sensor

Nissan Rogue Service Manual / Engine / Engine Control System / DTC/Circuit diagnosis / P0461 fuel level sensor

DTC Description

DTC DETECTION LOGIC

Driving long distances naturally affect fuel gauge level.

This diagnosis detects the fuel gauge malfunction of the gauge not moving even after a long distance has been driven.

DTC No.	CONSULT screen terms (Trouble diagnosis content)	DTC detecting condition
P0461	FUEL LEVEL SENSOR (Fuel level sensor ″A″ circuit range/performance)	The output signal of the fuel level sensor does not change within the specified range even though the vehicle has been driven a long distance.

POSSIBLE CAUSE

Harness or connectors (The CAN communication line is open or shorted.)
Harness or connectors (The sensor circuit is open or shorted.)
Combination meter
Fuel level sensor

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

1.CHECK DTC PRIORITY

If DTC P0461 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or P0607.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".

NO >> GO TO 2.

2.PRECONDITIONING

WARNING: When performing following procedure, be sure to observe the handling of the fuel. Refer to FL-2, "General Precaution".

TESTING CONDITION: Before starting component function check, preparation of draining fuel and refilling fuel is required.

Do you have CONSULT? YES >> GO TO 3.

NO >> GO TO 4.

3.PERFORM COMPONENT FUNCTION CHECK

With CONSULT

NOTE: Start from step 10, if it is possible to confirm that the fuel cannot be drained by 30 (7-7/8 US gal, 6-5/ 8 Imp gal) in advance.

Prepare a fuel container and a spare hose.
Release fuel pressure from fuel line, refer to EC-144, "Work Procedure".
Remove the fuel feed hose on the fuel level sensor unit.
Connect a spare fuel hose where the fuel feed hose was removed.
Turn ignition switch OFF and wait at least 10 seconds then turn ON.
Select “FUEL LEVEL SE” in “DATA MONITOR” mode of “ENGINE” using CONSULT.
Check “FUEL LEVEL SE” output voltage and note it.
Select “FUEL PUMP RELAY” in “ACTIVE TEST” mode of “ENGINE” using CONSULT.
Touch “ON” and drain fuel approximately 30 (7-7/8 US gal, 6-5/8 Imp gal) and stop it.
Check “FUEL LEVEL SE” output voltage and note it.
Fill fuel into the fuel tank for 30 (7-7/8 US gal, 6-5/8 Imp gal).
Check “FUEL LEVEL SE” output voltage and note it.
Confirm whether the voltage changes more than 0.03 V during step 7 to 10 and 10 to 12.

Is the inspection result normal? YES >> INSPECTION END

NO >> Proceed to EC-347, "Diagnosis Procedure".

4.PERFORM COMPONENT FUNCTION CHECK

Without CONSULT

NOTE: Start from step 8, if it is possible to confirm that the fuel cannot be drained by 30 (7-7/8 US gal, 6-5/8 Imp gal) in advance.

Prepare a fuel container and a spare hose.
Release fuel pressure from fuel line. Refer to EC-144, "Work Procedure".
Remove the fuel feed hose on the fuel level sensor unit.
Connect a spare fuel hose where the fuel feed hose was removed.
Turn ignition switch ON.
Drain fuel by 30 (7-7/8 US gal, 6-5/8 Imp gal) from the fuel tank using proper equipment.
Confirm that the fuel gauge indication varies.
Fill fuel into the fuel tank for 30 (7-7/8 US gal, 6-5/8 Imp gal).
Confirm that the fuel gauge indication varies.

Is the inspection result normal? YES >> INSPECTION END

NO >> Proceed to EC-347, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK DTC PRIORITY

If DTC P0461 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or P0607.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".

NO >> GO TO 2.

2.CHECK COMBINATION METER FUNCTION

Refer to MWI-21, "CONSULT Function (METER/M&A)".

Is the inspection result normal? YES >> GO TO 3.

NO >> Refer to MWI-62, "Component Function Check"

3.CHECK INTERMITTENT INCIDENT

Refer to GI-41, "Intermittent Incident".

>> INSPECTION END

P0460 fuel level sensor

DTC Description DTC DETECTION LOGIC When the vehicle is parked, naturally the fuel level in the fuel tank is stable. It means that output signal of the fuel level sensor does not change. If ECM s ...

P0462, P0463 fuel level sensor

DTC Description DTC DETECTION LOGIC This diagnosis indicates the former, to detect open or short circuit malfunction. DTC No. CONSULT screen terms (Trouble diagnosis content) DTC ...

Other materials:

DTC/circuit diagnosis
P1610 LOCK MODE Description ECM forcibly switches to the mode that inhibits engine start, when engine start operation is performed 5 times or more while communication between ECM and BCM is not normal. DTC Logic DTC DETECTION LOGIC NOTE: If DTC B1610 is displayed with DTC U1000, fi ...

U1000 CAN COMM circuit
Description CAN (Controller Area Network) is a serial communication system for real time application. It is an on-vehicle multiplex communication system with high data communication speed and excellent error detection ability. Many electronic control units are equipped into vehicles, and ea ...

Adjust
For adjustable head restraint/headrest Adjust the head restraint/headrest so the center is level with the center of your ears. If your ear position is still higher than the recommended alignment, place the head restraint/headrest at the highest position. For non-adjustable head restraint ...