Nissan Rogue Owners Manual: Text messaging

Nissan Rogue Owners Manual / Monitor, climate, audio, phone and voice recognition systems / Bluetooth® Hands-Free Phone System without Navigation System (if so equipped) / Text messaging

WARNING

Laws in some jurisdictions may restrict the use of “Text-to-Speech.” Check local regulations before using the feature.
Laws in some jurisdictions may restrict the use of some of the applications and features, such as social networking and texting. Check local regulations for any requirements.
Use the text messaging feature after stopping your vehicle in a safe location.
If you have to use the feature while driving, exercise extreme caution at all times so full attention may be given to vehicle operation.
If you are unable to devote full attention to vehicle operation while using the text messaging feature, pull off the road to a safe location and stop your vehicle.

NOTE: This feature is automatically disabled if the connected device does not support the Message Access Profile (MAP). Refer to the phone’s Owner’s Manual for details and instructions. The system allows for the sending and receiving of text messages through the vehicle interface.

Sending a text message:

Press the button.
Say “Messaging”.
Say “Send Text”.
The system will provide a list of available commands in order to determine the recipient of the text message. Choose from the following:

(A name)
Number
Incoming Calls
Outgoing Calls
Missed Calls

If “Incoming Calls”, “Outgoing Calls”, or “Missed Calls” is selected, the following additional commands will be displayed:

Send Text
Next Entry
Previous Entry

For additional information about these options, refer to “Voice commands” in this section.

5. Once a recipient is chosen, the system prompts for which message to send. Five predefined messages are available as well as three custom messages. To choose one of the predefined messages, speak one of the following:

“Driving, can’t text”
“Call me”
“On my way”
“Running late”
“Okay”

To send one of the custom messages, say “Custom Message”. If more than one custom message is stored, the system will prompt for the number of the desired custom message. For additional information on setting and managing custom text messages, refer to “Bluetooth® settings” in this section.

Reading a received text message:

Press the button.
Say “Messaging”.
Say “Read Text”.

The text message, sender and delivery time are shown on the screen. Use the tuning switch on the steering wheel to scroll through all text messages if more than one are available. Press the button to exit the text message screen.

Press the button to access the following options for replying to the text message:

Call Back
Speak this command to call the sender of the text message using the Bluetooth® Hands-Free Phone System.
Send Text
Speak this command to send a text message response to the sender of the text message.
Read Text
Speak this command to read the text message again.
Previous Text
Speak this command to move to the previous text message (if available).
Next Text
Speak this command to move to the next text message (if available).

NOTE: Text messages are only displayed if the vehicle speed is less than 5 mph (8 km/h).

Making a call

To make a call from a phone connected to the vehicle’s Bluetooth® Hands-Free Phone System: Press the button. The system will prompt you for a command. Say “Call”. ...

Manual control

While using the Voice Recognition system, it is possible to select menu options by using the steering wheel controls instead of speaking voice commands. To activate manual control mode, press ...

Other materials:

Cluster lid A
Removal and Installation REMOVAL Remove instrument lower panel LH. Refer to IP-22, "Removal and Installation". Remove instrument finisher A. Refer to IP-15, "INSTRUMENT FINISHER A : Removal and Installation". Remove instrument finisher B. Refer to ...

Symptom diagnosis
SQUEAK AND RATTLE TROUBLE DIAGNOSES Work Flow CUSTOMER INTERVIEW Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diagnostic Worksheet during the interview to document the facts and conditions when the noise occurs and any custome ...

DTC/circuit diagnosis
U1000 CAN COMM CIRCUIT Description Refer to LAN-8, "System Description". DTC Logic DTC DETECTION LOGIC NOTE: U1000 can be set if a module harness was disconnected and reconnected, perhaps during a repair. Confirm that there are actual CAN diagnostic symptoms and a present DTC by p ...