Nissan Rogue Service Manual: Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT
PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”,
used along
with a front seat belt, helps to reduce the risk or severity of injury to the
driver and front passenger for certain
types of collision. Information necessary to service the system safely is
included in the SR and SB section of
this Service Manual.
WARNING:
- To avoid rendering the SRS inoperative, which could increase
the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all
maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
- Improper maintenance, including incorrect removal and
installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of
Spiral Cable and Air Bag
Module, see the SR section.
- Do not use electrical test equipment on any circuit related to
the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or
orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
- When working near the Airbag Diagnosis Sensor Unit or other
Airbag System sensors with the Ignition
ON or engine running, DO NOT use air or electric power tools or strike near
the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air
bag(s), possibly causing
serious injury.
- When using air or electric power tools or hammers, always
switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Service Notice and Precautions for TPMS
WARNING:
Radio waves could adversely affect electric medical equipment. Those who use a
pacemaker should
contact the electric medical equipment manufacturer for the possible influences
before use.
- Low tire pressure warning lamp blinks for 1 minute, then turns ON
when occurring any malfunction except
low tire pressure. Erase the self-diagnosis memories for Tire Pressure
Monitoring System (TPMS), or register
the ID to turn low tire pressure warning lamp OFF. For ID registration,
refer to WT-20, "Work Flow".
- ID registration is required when replacing or rotating wheels,
replacing tire pressure sensor or low tire pressure
warning control unit. Refer to WT-21, "Work Procedure".
- Replace grommet seal, valve core and valve cap of tire pressure
sensor in TPMS, when replacing each tire
by reaching the wear limit. Refer to WT-61, "Removal and Installation".
- Because the tire pressure sensor conforms to North America radio
law, the following items must be
observed.
- The sensor may be used only in North America.
- It may not be used in any method other than the specified method
- It must not be disassembled or modified.
Service Notice and Precautions for Road Whee
- Genuine NISSAN aluminum wheel is designed for each type of vehicle. Use
it on the specified vehicle only.
- Use Genuine NISSAN parts for the road wheels, valve caps and wheel
nuts.
- Always use them after adjusting the wheel balance. For the balance
weights, use Genuine NISSAN aluminum
wheel weights.
- Use caution when handling the aluminum wheels, because they can be
easily scratched. When removing
dirt, do not use any abrasives, a wire brush, or other items that may
scratch the coating. Use a neutral detergent
if a detergent is needed.
- After driving on roads scattered with anti-icing salts, wash off
the wheels completely.
- When installing road wheels onto the vehicle, always wipe off any
dirt or foreign substances to prevent them
from being trapped between the contact surfaces of wheel.
- Do not apply oil to nut and bolt threads.
- When tightening the valve cap there is a risk of damaging the
valve cap if a tool is used. Tighten by hand.
Special Service Tool
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
—
(J-50190)
Signal Te ...
Other materials:
System description
SYSTEM
System Description
SYSTEM DIAGRAM
SYSTEM DESCRIPTION
The BCM has a CAN gateway function.
The BCM communicates between two CAN communication circuits.
The BCM selects and transmits only necessary information.
DIAGNOSIS SYSTEM (CAN GATEWAY)
CONSULT Function
...
Removal and installation
FRONT COIL SPRING AND STRUT
Exploded View
Strut mount insulator
Rotary stop
Front spring upper rubber seat
Front suspension bound bumper
Front spring
Front spring lower rubber seat
Stabilizer connecting rod
Strut
Steering knuckle
Removal and Installation
REMO ...
Rear bumper
Exploded View
Rear bumper fascia side bracket
(LH)
Rear mud protector
Rear bumper reinforcement support
(LH)
Rear bumper fascia undercover
(LH)
Rear bumper reinforcement
Rear energy absorber
Rear bumper bracket (LH)
Rear bumper fascia
Rear bumper fascia re ...
© 2014-2025 Copyright www.nirogue.com