Nissan Rogue Owners Manual: Navigation System voice commands

Nissan Rogue Owners Manual / Monitor, climate, audio, phone and voice recognition systems / NISSAN Voice Recognition System (if so equipped) / Navigation System voice commands

The following voice commands are available for the Navigation System:

Street Address (address)
Points of Interest (name)
POI by Category
Home
Address Book
Previous Destinations
Enter Address in Steps
Cancel Route

For additional information about these commands, refer to the separate Navigation System Owner’s Manual.

Audio system voice commands

To access the audio system voice commands:

Press the button.
Say “Audio”
Speak a command from the following available commands:

Play (AM, FM, etc.)
Allows user to select radio band
Tune AM (number)
Allows user to tune directly to a desired AM frequency
Tune FM (number)
Allows user to tune directly to a desired FM frequency
SXM channel (number)
Allows user to tune directly to a desired SXM station (if so equipped)
CD Track (number)
Allows user to select track to be played
Play Song (name)
Allows user to select song name to be played
Play Artist (name)
Allows user to select artist to be played
Play Album (name)
Allows user to select album name to be played

For additional information about the audio system, refer to “Audio system” in this section.

Information voice commands

The following voice commands are available for the information functions of the Navigation System:

Traffic
Fuel Prices
Stocks
Movie Listings
Current Weather
Weather Map
5 — day Forecast
6 — hour Forecast

For additional information about these commands, refer to the separate Navigation System Owner’s Manual.

My Apps Voice Commands

Many Apps can be accessed using this voice command. For additional information, refer to “NissanConnectSM with Mobile Apps” in this section.

Help voice commands

The following voice commands can be spoken to have the system provide instructions and tips for using the NISSAN Voice Recognition system.

List Commands
What Can I Say?
General Help
Quit
Exit

Troubleshooting guide

The system should respond correctly to all voice commands without difficulty. If problems are encountered, follow the solutions given in this guide for the appropriate error. Where the solutions are listed by number, try each solution in turn, starting with number one, until the problem is resolved.

Symptom/error message

Solution

The system responds “Command Not Recognized” or the system fails to recognize the command correctly.

Ensure that the command format is valid. Use the “List Commands” or “What Can I Say?” command under the “Help” menu.
Speak clearly without pausing between words and at a level appropriate to the ambient noise level.
Ensure that the ambient noise level is not excessive (for example, with the windows open or the defroster on).

NOTE: If it is too noisy to use the phone, it is likely that voice commands will not be recognized.

If optional words of the command have been omitted, then the command should be tried with these in place.

Bluetooth® Hands-Free Phone System voice commands

To access the Bluetooth® Hands-Free Phone System voice commands: Press the button. Say “Call” and then a name in the vehicle phonebook to call that entry. Otherwise, say � ...

Starting and driving

...

Other materials:

Personal lamp
Removal and Installation The personal lamp is serviced as part of headlining. Refer to INT-30, "Removal and Installation". Bulb or Lens Replacement WARNING: Do not touch the glass surface of a bulb while it is lit or right after being turned OFF to prevent burns. CAUTION: &n ...

Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the ...

P0222, P0223 TP sensor
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P0222 TP SEN 1/CIRC-B1 (Throttle/pedal position sensor/switch ″B″ circuit low) An excessively low voltage from the TP sensor 1 is se ...