Nissan Rogue Service Manual: Basic inspection

Nissan Rogue Service Manual / Restraints / SRS Airbag / Basic inspection

COLLISION DIAGNOSIS

FOR FRONTAL COLLISION

FOR FRONTAL COLLISION : When SRS is activated in a collision

CAUTION: Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

Before performing any of the following steps, ensure that all vehicle body and structural repairs have been completed.
Replace the diagnosis sensor unit.
Remove the front air bag modules, crash zone sensor, bracket and seat belt pre-tensioner assemblies.
Check the SRS components using the table below: Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)
Install new front air bag modules, crash zone sensor assembly, bracket and seat belt pre-tensioner assemblies.
Perform self-diagnosis using CONSULT or air bag warning lamp. Refer to SRC-16, "Description" for details. Ensure entire SRS operates properly.
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to SRC-16, "Description".

SRS INSPECTION (FOR FRONTAL COLLISION)

Part	Inspection
Driver air bag module	If the driver air bag has deployed: REPLACE Install with new fasteners.
Front passenger air bag module (if equipped)	If the front passenger air bag has deployed: REPLACE Install with new fasteners.
Crash zone sensor	If any of the front air bags or seat belt pre-tensioners* have been activated: REPLACE the crash zone sensor and bracket with new fasteners. *: Confirm seat belt pre-tensioner activation using CONSULT only.
Seat belt pre-tensioner assemblies (All applicable locations: buckle, retractor, lap outer)	If either the driver or passenger seat belt pre-tensioner* has been activated: REPLACE all seat belt pre-tensioner assemblies with new fasteners. *: Confirm seat belt pre-tensioner activation using CONSULT only.
Diagnosis sensor unit	If any of the SRS components have been activated: REPLACE the diagnosis sensor unit. Install with new fasteners.
Steering wheel	Visually check steering wheel for deformities. Check harness (built into steering wheel) and connectors for damage, and terminals for deformities. Install driver air bag module into the steering wheel to check fit and alignment with the wheel. Check steering wheel for excessive free play. If no damage is found, reinstall. If damaged − REPLACE.
Spiral cable	If the driver front air bag has deployed: REPLACE the spiral cable.
Occupant classification system (Passenger seat)	Remove passenger seat assembly. Check control unit case for dents, cracks of deformities. Check connectors and pressure sensor tube for damage, and terminals for deformities. Check seat frame and cushion pan for dents or deformities. If no damage is found, reinstall seat with new fasteners. If damaged − REPLACE seat cushion assembly with new fasteners. Perform zero point reset function after front passenger seat is installed in the vehicle and all bolts are tightened to specification. Refer to SRC-42, "ZERO POINT RESET : Description".
Harness and connectors	Check connectors for poor connection, damage, and terminals for deformities. Check harness for binding, chafing, cuts, or deformities. If no damage is found, reinstall the harness and connectors. If damaged − REPLACE the damaged harness. Do not attempt to repair, splice or modify any SRS harness
Instrument panel assembly	If the front passenger air bag has deployed: REPLACE the instrument panel assembly. (integrated type)

FOR FRONTAL COLLISION : When SRS is not activated in a collision

CAUTION: Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

Before performing any of the following steps, ensure that all vehicle body and structural repairs have been completed.
Check the SRS components using the table below: Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)
Perform self-diagnosis using CONSULT or air bag warning lamp. Refer to SRC-16, "Description" for details. Ensure entire SRS operates properly.
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to SRC-16, "Description".
SRS INSPECTION (FOR FRONTAL COLLISION)

Part	Inspection
Driver air bag module	If the driver air bag has NOT been deployed: Remove driver air bag module. Check harness cover and connectors for damage, terminals for deformities, and harness for binding. Install driver air bag module into the steering wheel to check fit and alignment with the wheel. If no damage is found, reinstall with new fasteners. If damaged − REPLACE. Install driver air bag module with new fasteners.
Front passenger air bag module (if equipped)	If the front passenger air bag has NOT been deployed: Remove front passenger air bag module. Check harness cover and connectors for damage, terminals for deformities, and harness for binding. Install front passenger air bag module into the instrument panel to check fit with the instrument panel. If no damage is found, reinstall with new fasteners. If damaged − REPLACE. Install front passenger air bag modules with new fasteners.
Crash zone sensor	If the front air bags or seat belt pre-tensioners have NOT been activated: Remove the crash zone sensor. Check harness connectors for damage, terminals for deformities, and harness for binding. Check for visible signs of damage (dents, cracks, deformation, etc.) of the crash zone sensor and bracket. Install the crash zone sensor to check fit. If no damage is found, reinstall with new fasteners. If damaged − REPLACE the crash zone sensor and bracket with new fasteners.
Seat belt pre-tensioner assemblies (All applicable locations: buckle, retractor, lap outer)	If the pre-tensioners have NOT been activated: Remove seat belt pre-tensioners. Check harness cover and connectors for damage, terminals for deformities, and harness for binding. Check belts for damage and anchors for loose mounting. Check retractor for smooth operation. Check seat belt adjuster for damage. Check for deformities of the center pillar inner. If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly. If no damage is found, reinstall seat belt pre-tensioner assembly. If damaged − REPLACE. Install the seat belt pre-tensioners with new fasteners.
Diagnosis sensor unit	If none of the SRS components have been activated: Check case for dents, cracks or deformities. Check connectors for damage, and terminals for deformities. If no damage is found, reinstall with new fasteners. If damaged − REPLACE. Install diagnosis sensor unit with new fasteners.
Steering wheel	Visually check steering wheel for deformities. Check harness (built into steering wheel) and connectors for damage, and terminals for deformities. Install driver air bag module into the steering wheel to check fit and alignment with the wheel. Check steering wheel for excessive free play. If no damage is found, reinstall. If damaged − REPLACE.
Spiral cable	If the driver front air bag has not deployed: Visually check spiral cable and combination switch for damage. Check connectors and protective tape for damage. Check steering wheel for noise, binding or heavy operation. If no damage is found, reinstall. If damaged − REPLACE.
Occupant classification system (Passenger seat)	Remove passenger seat assembly. Check control unit case for dents, cracks of deformities. Check connectors and pressure sensor tube for damage, and terminals for deformities. Check seat frame and cushion pan for dents or deformities. If no damage is found, reinstall seat with new fasteners. If damaged − REPLACE seat cushion assembly with new fasteners. Perform zero point reset function after front passenger seat is installed in the vehicle and all bolts are tightened to specification. Refer to SRC-42, "ZERO POINT RESET : Description".
Harness and connectors	Check connectors for poor connection, damage, and terminals for deformities. Check harness for binding, chafing, cuts, or deformities. If no damage is found, reinstall the harness and connectors. If damaged − REPLACE the damaged harness. Do not attempt to repair, splice or modify any SRS harness.
Instrument panel assembly	If the front passenger air bag has NOT deployed: Visually check instrument panel assembly for damage. If no damage is found, reinstall the instrument panel assembly. If damaged − REPLACE the instrument panel assembly.

FOR SIDE AND ROLLOVER COLLISION

FOR SIDE AND ROLLOVER COLLISION : When SRS is activated in a collision

CAUTION: Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

Before performing any of the following steps, ensure that all vehicle body and structural repairs have been completed.
Replace the following components:

Front seat back assembly (on the side on which side air bag is activated)
Door finisher (on the side on which door-mounted curtain air bag is activated)
Pop-up roll bar assemblies and pop-up roll bar covers
Side air bag (satellite) sensor LH/RH (on the side on which side air bag is activated)
Diagnosis sensor unit
Seat belt pre-tensioner assemblies

Check the SRS components and the related parts using the following table.
Replace any SRS components and the related parts showing visible signs of damage. (dents, cracks, deformation, etc.)
Perform self-diagnosis using CONSULT and “AIR BAG” warning lamp. Refer to SRC-16, "Description" for details. Make sure entire SRS operates properly.
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to SRC-16, "Description".

SRS INSPECTION (FOR SIDE AND ROLLOVER COLLISION)

Part	Inspection
Side curtain air bag module LH	If the side curtain air bag LH has deployed: REPLACE the side curtain air bag module LH. Install with new fasteners.
Side curtain air bag module RH	If the side curtain air bag RH has deployed: REPLACE the side curtain air bag module RH. Install with new fasteners.
Front side air bag module LH	If the front side air bag LH has deployed: REPLACE front seatback assembly LH.
Front side air bag module RH	If the front side air bag RH has deployed: REPLACE front seatback assembly RH.
Side air bag (satellite) sensor (LH or RH)	If any of the SRS components have deployed: REPLACE the side air bag (satellite) sensor on the collision side with new fasteners.
Diagnosis sensor unit	If any of the SRS components have deployed: REPLACE the diagnosis sensor unit with new fasteners.
Seat belt pre-tensioner assemblies (All applicable locations: buckle, retractor, lap outer)	If either the driver or passenger seat belt pre-tensioner* has been activated: REPLACE all seat belt pre-tensioner assemblies with new fasteners. *: Confirm seat belt pre-tensioner activation using CONSULT only.
Center inner pillar	Check the center inner pillar on the collision side for damage (dents, cracks, deformation, etc.). If damaged − REPAIR the center inner pillar.
Trim/headlining	Check for visible signs of damage (dents, cracks, deformation, etc.) of the interior trim on the collision side. If damaged − REPLACE the damaged trim parts.
Door-mounted curtain air bag module LH	If the door-mounted curtain air bag module LH has deployed: REPLACE the door finisher LH and door-mounted curtain air bag module. Install with new fasteners.
Door-mounted curtain air bag module RH	If the door-mounted curtain air bag module RH has deployed: REPLACE the door finisher RH and door-mounted curtain air bag module. Install with new fasteners.
Occupant classification system (Passenger seat)	Remove passenger seat assembly. Check control unit case for dents, cracks of deformities. Check connectors and pressure sensor tube for damage, and terminals for deformities. Check seat frame and cushion pan for dents or deformities. If no damage is found, reinstall seat with new fasteners. If damaged − REPLACE seat cushion assembly with new fasteners. Perform zero point reset function after front passenger seat is installed in the vehicle and all bolts are tightened to specification. Refer to SRC-42, "ZERO POINT RESET : Description".
Pop-up roll bar assemblies	If the pop-up roll bar has deployed: REPLACE pop-up roll bar assemblies and pop-up roll bar covers. Install with new fasteners.

FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a collision

CAUTION: Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

Before performing any of the following steps, ensure that all vehicle body and structural repairs have been completed.
Check the SRS components and the related parts using the following table.

If the front seat back assembly is damaged, the front seat back assembly must be replaced.
If the door finisher assembly is damaged, the door finisher assembly and door-mounted curtain air bag module must be replaced.

Perform self-diagnosis using CONSULT and “AIR BAG” warning lamp. Refer to SRC-16, "Description" for details. Make sure entire SRS operates properly.
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to SRC-16, "Description".

SRS INSPECTION (FOR SIDE AND ROLLOVER COLLISION)

Part	Inspection
Side curtain air bag module LH	If the side curtain air bag LH has NOT deployed: Check for visible signs of damage (dents, tears, deformation, etc.) of the center pillar on the collision side. If damaged − Remove the side curtain air bag module LH. Check for visible signs of damage (tears etc.) of the side curtain air bag module LH. Check harness and connectors for damage, and terminals for deformities. If no damage is found, reinstall the side curtain air bag module LH with new fasteners. If damaged − REPLACE the side curtain air bag module LH with new fasteners.
Side curtain air bag module RH	If the side curtain air bag RH has NOT deployed: Check for visible signs of damage (dents, tears, deformation, etc.) of the center pillar on the collision side. If damaged − Remove the side curtain air bag module RH. Check for visible signs of damage (tears etc.) of the side curtain air bag module RH. Check harness and connectors for damage, and terminals for deformities. If no damage is found, reinstall the side curtain air bag module RH with new fasteners. If damaged − REPLACE the side curtain air bag module RH with new fasteners.
Front side air bag module LH	If the front side air bag LH has NOT deployed: Check for visible signs of damage (dents, tears, deformation, etc.) of the seat back on the collision side. Check harness and connectors for damage, and terminals for deformities. If damaged − REPLACE the front seatback assembly LH.
Front side air bag module RH	If the front side air bag RH has NOT deployed: Check for visible signs of damage (dents, tears, deformation, etc.) of the seat back on the collision side. Check harness and connectors for damage, and terminals for deformities. If damaged − REPLACE the front seatback assembly RH.
Side air bag (satellite) sensor (LH or RH)	If none of the SRS components have been activated: Remove the side air bag (satellite) sensor (LH or RH) on the collision side. Check harness connectors for damage, terminals for deformities, and harness for binding. Check for visible signs of damage (dents, cracks, deformation, etc.) of the side air bag (satellite) sensor (LH or RH). Install the side air bag (satellite) sensor (LH or RH) to check fit. If no damage is found, reinstall the side sir bag (satellite) sensor (LH or RH) with new fasteners. If damaged − REPLACE the side air bag (satellite) sensor (LH or RH) with new fasteners
Diagnosis sensor unit	If none of the SRS components have been activated: Check case and bracket for dents, cracks or deformities. Check connectors for damage, and terminals for deformities. If no damage is found, reinstall the diagnosis sensor unit with new fasteners. If damaged − REPLACE the diagnosis sensor unit with new fasteners.
Seat belt pre-tensioner assemblies (All applicable locations: buckle, retractor, lap outer)	If the pre-tensioners have NOT been activated: Remove seat belt pre-tensioners. Check harness cover and connectors for damage, terminals for deformities, and harness for binding. Check belts for damage and anchors for loose mounting. Check retractor for smooth operation. Check seat belt adjuster for damage. Check for deformities of the center pillar inner. If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly. If no damage is found, reinstall seat belt pre-tensioner assembly. If damaged − REPLACE. Install the seat belt pre-tensioners with new fasteners.
Seat (with front side air bag)	If the front LH or front RH side air bag modules have NOT deployed: Visually check the seat on the collision side. Remove the seat on the collision side and check the following for damage and deformities. Harness, connectors and terminals Frame and recliner (for front and rear seat), and also adjuster and slides (for front seat) If no damage is found, reinstall the seat. If damaged − REPLACE the damaged seat parts using new fasteners. If the front seat back is damaged, the front seat back assembly must be replaced.
Center inner pillar	Check the center inner pillar on the collision side for damage (dents, cracks, deformation, etc.). If damaged − REPAIR the center inner pillar.
Trim/headlining	Check for visible signs of damage (dents, cracks, deformation, etc.) of the interior trim on the collision side. If damaged − REPLACE the damaged trim parts.
Door-mounted curtain air bag module LH	If the door-mounted curtain air bag LH has NOT deployed: Check for visible signs of damage (dents, tears, deformation, etc.) of the door finisher on the collision side. If damaged − REPLACE the door finisher LH with new fasteners. Check for visible signs of damaged (tears etc.) of the door-mounted curtain air bag module LH. Check harness and connectors for damage, and terminals for deformities. If no damage is found, reinstall door finisher. CAUTION: When removing door-mounted curtain air bag module from door finisher, never reuse door finisher. If damaged − REPLACE the door finisher LH and door-mounted curtain air bag module LH with new fasteners.
Door-mounted curtain air bag module RH	If the door-mounted curtain air bag RH has NOT deployed: Check for visible signs of damage (dents, tears, deformation, etc.) of the door finisher on the collision side. If damaged − REPLACE the door finisher RH with new fasteners. Check for visible signs of damage (tears etc.) of the door-mounted curtain air bag module RH. Check harness and connectors for damage, and terminals for deformities. If no damage is found, reinstall door finisher. CAUTION: When removing door-mounted curtain air bag module from door finisher, never reuse door finisher. If damaged − REPLACE the door finisher RH and door-mounted curtain air bag module RH with new fasteners.
Occupant classification system (Passenger seat)	Remove passenger seat assembly. Check control unit case for dents, cracks of deformities. Check connectors and pressure sensor tube for damage, and terminals for deformities. Check seat frame and cushion pan for dents or deformities. If no damage is found, reinstall seat with new fasteners. If damaged − REPLACE seat cushion assembly with new fasteners. Perform zero point reset function after front passenger seat is installed in the vehicle and all bolts are tightened to specification. Refer to SRC-42, "ZERO POINT RESET : Description".
Pop-up roll bar	If the pop-up roll bar has NOT deployed: Check for visible signs of damage (dents, tears, deformation, etc.) of the pop-up roll bar. If damaged − REPLACE the pop-up roll bar with new fasteners. Check harness and connectors for damage, and terminals for deformities. If no damage is found, reinstall the pop-up roll bar with new fasteners. Check for visible signs of damage (dents, cracks, deformation, etc.) of the seatback support brace assembly. If damaged − REPAIR the seatback support brace assembly.

Preparation

Special Service Tools The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description — (J-46534) Trim ...

Other materials:

Heated seat switch
Exploded View Center console cup holder Driver heated seat switch Passenger heated seat switch Switch carrier Pawl Removal and Installation REMOVAL Remove the center console cup holder. Refer to IP-18, "Exploded View". Remove screws fro ...

C1770, C1771, C1772, C1773 G sensor
DTC Description DTC DETECTION LOGIC DTC Display Item Malfunction Detected Condition Possible Causes C1770 G SENSOR FL (G sensor front left) Malfunction in the G sensor data from front left wheel sensor. Tire pressure sensor Tire pressure rece ...

Front wiper does not operate
Description The front wiper does not operate under any operation conditions. Diagnosis Procedure Regarding Wiring Diagram information, refer to WW-22, "Wiring Diagram". 1. CHECK WIPER RELAY OPERATION CONSULT ACTIVE TEST Select FR WIPER of BCM (WIPER) active test item. &nb ...

Nissan Rogue Service Manual: Basic inspection

Preparation

Removal and installation

Other materials: